Beginner's Plumbing: What You Need for Bathtub Installation
Beginner's Plumbing: What You Need for Bathtub Installation
Blog Article
Are you in search of related information on Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't precisely brain surgery, but it does call for strong plumbing, carpentry, and also in some cases, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably tough job. If the old bathtub is easily accessible, the task can relocate rapidly; if you have to open up a wall surface to get rid of the old tub and place the new bath tub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old bathtub as well as set in the new one. Make sure you have actually qualified yourself for the task as well as are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This write-up will assist you set up a new tub in your shower room if you have currently gotten a brand-new bathtub as well as do not need to transform the setup of your previous supply of water pipelines.
Your devices and material checklist must consist of the following:
Getting ready for the Installation
First of all, the supporting structure supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you use every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be quite problematic due to the restricted access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning during this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using the two wooden boards under its feet, place the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bath tub until the spirit level checks out degree.
To install faucets, fit all-time low of the outermost adaptable tap port to the suitable supply pipe by making a compression join; after that do the very same for the other tap.
Switch on the water system and examine all joints as well as brand-new pipework for leakages and also tighten them if needed. Fill the tub and additionally inspect the overflow outlet and also the regular outlet for leaks.
Lastly, repair the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the tub should wait until the bath tub has been used a minimum of when as this will resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in location between the faucet as well as the sink. Secure the tap in place with the maker offered backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind ought to be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a rigid seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, bring about issues with dampness and also feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components and fittings. They are offered in tubes as well as cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealer can break relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that blog entry on How to Install a Bathtub Yourself when browsing on the web. Liked our entry? Please share it. Help somebody else check it out. Thank-you for going through it.
Plumbing integrity assured. Report this page